aluminum electrolytic capacitors lr series chip type, high voltage. chip type, high voltage. applicable to automatic mounting machine using carrier tape. adapted to the rohs directive (2011/65/eu). lr lv long life ux high voltage measurement frequency : 120hz at 20 c specifications category temperature range rated voltage range rated capacitance range capacitance tolerance leakage current tangent of loss angle (tan ) stability at low temperature endurance shelf life resistance to soldering heat marking performance characteristics item 40 to +105 c 160 to 500v 2.7 to 39f 20% at 120hz, 20 c black print on the case top. the specifications listed at right shall be met when the capacitors are restored to 20 c after the rated voltage is applied for 3000 hours at 105 c. after storing the capacitors under no load at 105 c for 1000 hours and then performing voltage treatment based on jis c 5101-4 clause 4.1 at 20 c, they shall meet the specified values for the endurance characteristics listed above. the capacitors are kept on a hot plate for 30 seconds, which is maintained at 250 c and then performing voltage treatment based on jis c 5101-4 clause 4.1 at 20 c, they shall meet the characteristic requirements listed at right when they are removed from the plate. rated voltage (v) tan (max.) 160 0.20 200 0.20 250 0.25 400 0.25 450 0.30 500 0.30 capacitance change leakage current tan within 10% of the initial capacitance value less than or equal to the initial specified value less than or equal to the initial specified value capacitance change leakage current tan within 20% of the initial capacitance value less than or equal to the initial specified value 200% or less than the intial specified value after 1 minute's application of rated voltage, leakage current is not more than 0.04cv +100 (a). z 40 c / z+20 c rated voltage (v) impedance ratio zt / z20 (max.) 200 6 160 6 measurement frequency: 120hz 500 15 450 15 400 10 250 10 series voltage(2g : 400v) lot no. plastic platform 0.3max. d0.5 b0.2 a 0.2 a0.2 c0.2 0.5max. e h positive negative u 1 l 2 r 3 2 4 g 5 8 6 r 7 2 8 m 9 n 10 l 11 1 12 g 13 s 14 configuration taping code capacitance tolerance ( 20%) rated capacitance ( 8.2f ) rated voltage ( 400v ) series name type l1.0 8 10 d l a b c e 2.9 8.3 8.3 3.1 10 10 3.2 10.3 10.3 4.5 10 13.5 3.2 10.3 10.3 4.5 l 10 10 13.5 h 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 (mm) trade mark a2 8.2 2g lr pressure relief vent capacitance chip type ( 8 10l, 10) type numbering system (example : 400v 8.2 f) dimensions 2.7 3.9 4.7 5.6 6.8 8.2 10 12 15 22 27 33 39 2r7 3r9 4r7 5r6 6r8 8r2 100 120 150 220 270 330 390 8 10 10 10 10 13.5 8 10 10 10 10 13.5 8 10 10 10 10 13.5 8 10 10 10 10 13.5 8 10 10 10 10 13.5 8 10 10 10 10 13.5 50 65 70 50 65 70 35 50 55 35 50 55 25 40 45 20 35 40 2c 2d 2e 2g 2w 160 200 250 400 450 2h 500 v code cap.(f) rated ripple case size d l (mm) frequency coefficient of rated ripple current coefficient frequency 50 hz 0.80 1.00 1.25 1.40 1.60 120 hz 300 hz 1 khz 10 khz or more taping specifications are given in page 23. recommended land size, soldering by reflow are given in page 18, 19. please refer to page 3 for the minimum order quantity. rated ripple current (marms) at 105 c 120hz voltage v 160 200 250 400 450 500 code 2c 2d 2e 2g 2w 2h cat.8100c
|
